How To Install 50 Inch Curved Light Bar

Full general Recommendations:

Go on these steps in mind for every installation.

Bench exam everything prior to installation.
Do not over tighten hardware.
Keep all lights and wires away from moving parts.
Keep all lights and wires abroad from high heat sources, brake components, frazzle components, coolant systems.
Double check proper aiming to yield the best results.
Secure wiring to avoid damage.
Fuse all connections within eighteen" of battery/power source.
See our Off Road Low-cal Bars FAQ page for more data.

Download Off-Road LED Light Bar Wiring Transmission

Find a suitable mounting location that will allow for running wires and mounting the LED light(s). Lay out and mark where the mounting holes will be positioned. Drill appropriate-sized pigsty(s) for the mounting hardware. Before starting to drill hole(s), check backside locations to insure nothing volition be damaged while drilling light mounting holes.
Mountain the lights with the provided hardware, beingness sure not to over tighten the hardware (you will need to adjust them in Step seven). Optional mounting brackets (MODLED-BK), clamps (MODCLx-BK), and magnetic mounting systems (WL-MB) are available.
Road the lighting side of the wiring harness from the bombardment to the calorie-free(southward) in a rubber, secure manner. Connect the harness to the light(s). Exist sure to avoid estrus sources and any moving parts while running your wires. Prolonged chafing of the wires may atomic number 82 to a curt in the circuit. Typically, following the vehicle manufacturer's wiring harness is a safe path to follow. Some lights may not accept DT or ATP connections on them but the connectors tin can be added from the harness kit or purchased separately (DT-FPT or ATP-FPT).

Go along to road the switch portion of the harness to the desired location of the switch. The switch may need to be unplugged from the harness to make routing of the harness easier. An optional remote-controlled switch (RCS-RF25A) tin be utilized to speed up the time of an install and avoid routing wires through the firewall. Be certain to double-check for all obstructions and proper clearances. Drill an appropriate-sized hole for the switch. Connect the wires to the switch and mount the switch. Illuminated rectangular rocker switches (RS-x) are also available with dissimilar legends.
Connect the black (ground) wire with the large ring concluding from the harness to the negative battery concluding. Connect the cherry-red (power) wire with the big ring terminal from the harness to the positive bombardment terminal.
Secure the relay to a suitable location and test the lights to brand sure the excursion works.
Finally, aim the lights in the desired management and tighten all the mounting hardware.

Wiring with Super Bright LEDs Harness

Wiring w/ Existing Light Wiring

Disconnect existing lighting circuit from the battery or merely remove the existing fuse. Find a suitable mounting location that will allow for running wires and mounting the LED low-cal(s). Lay out and mark where the mounting holes will be positioned. Drill appropriate-sized hole(s) for the mounting hardware. Before starting to drill pigsty(southward), cheque behind locations to insure zip will exist damaged while drilling low-cal mounting holes.
Mount the lights with the provided hardware, beingness sure not to over tighten the hardware (you lot volition need to arrange them in Step 4). Optional mounting brackets (MODLED-BK), clamps (MODCLx-BK), and magnetic mounting systems (WL-MB) are bachelor.
Connect the footing wire of the new light to the ground wire of the onetime light with solder and estrus shrink tubing (DWS-x) or perma-seal butt connectors (PSC-x). Connect the power wire of the new low-cal to the power wire of the former light with solder and rut shrink tubing (DWS-x) or perma-seal butt connectors (PSC-x).
If the new LED work light or off road light bar has an ATP or DT connector that you wish to utilize, the corresponding ATP (ATP-MPT) or DT (DT-MPT) pigtails are available.
Finally, aim the lights in the proper direction and tighten all the mounting hardware.

Wiring Pigtail w/o Harness

Observe a suitable mounting location that will let for running wires and mounting the LED light(s). Lay out and mark where the mounting holes will be positioned. Drill advisable-sized hole(southward) for the mounting hardware. Earlier starting to drill hole(s), bank check behind locations to insure naught will be damaged while drilling calorie-free mounting holes.
Mountain the lights with the provided hardware, existence sure not to over tighten the hardware (you lot will need to adjust them in Step 6). Optional mounting brackets (MODLED-BK), clamps (MODCLx-BK), and magnetic mounting systems (WL-MB) are bachelor.
Route the wiring from the battery to the light(due south) in a safe, secure manner. Connect the negative wire to the black wire of the pigtail (DT-MPT or ATP-MPT). Connect the positive wire to the input terminal of the switch. Then connect the output final of the switch to the red wire of the pigtail (DT-MPT or ATP-MPT). Exist sure to avoid oestrus sources and whatsoever moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer's wire harness is a safe path to follow.
Continue to route wires to the desired location of the switch (RS-x, RRS-SPx, or WRRS-SPR). An optional, remote-controlled switch (RCS-RF25A) can be utilized to speed up the fourth dimension of an install and avoid routing wires through the firewall. Be sure to double bank check for all obstructions and proper clearance. Drill an appropriate sized hole for the switch. Connect the wires to the switch and mountain the switch.
Connect the ground wire to the negative battery terminal. Then connect the other final of the switch to the positive battery final with an accordingly-sized fuse holder (WMFH) and fuse (MAF-x), installed inside 18 inches of the battery.
Finally, aim the lights in the proper direction and tighten all the mounting hardware.

Wiring with Existing Light Wiring